Antminer Z9 Miner_Ctrlboard_V1.1 ремонт платы, фото

Bitmain Antminer Z9 Miner_Ctrlboard_V1.1

U1 A-R 1-15 bga Процессор: Xilinx xc7z007s clg225apx

U2 tsop48 Flash: Micron 29F2G08ABAEA 256MByte

U3 A-T 1-9 bga Ram: 7UK17 D9UTK Micron BHFQ DDR3?

Не мигает светодиод D3, не горит светодиод D1, светится зеленым D12 (V+3.3). Везде есть напряжения V3.3, V1.8, V1.0 V1.5, на FB2 земля и 0.9mv. Замена флешки nand MT29F2G08ABAEA не дала результата. В лог ничего не сыпет. Подозрение на проц xc7z007s. (xc7z007s-clg225abx1801) Soc Zynq Zynq-7000 Zynq-7000S

TTL com port j5 rxd gnd txd log: Прилагаю Лог с живой платы.

Xilinx First Stage Boot Loader
Release 2017.1  Mar 12 2018-19:08:47
Devcfg driver initialized
Silicon Version 3.1
Boot mode is NAND
                 InitNand: Geometry = 0x8
Nand driver initialized
NAND Init Done
Flash Base Address: 0xE1000000
Reboot status register: 0x60400000
Multiboot Register: 0x0000C000
Image Start Address: 0x00000000
Partition Header Offset:0x00000C80
Partition Count: 3
Partition Number: 1
Header Dump
Image Word Len: 0x0007F2E8
Data Word Len: 0x0007F2E8
Partition Word Len:0x0007F2E8
Load Addr: 0x00000000
Exec Addr: 0x00000000
Partition Start: 0x000075D0
Partition Attr: 0x00000020
Partition Checksum Offset: 0x00000000
Section Count: 0x00000001
Checksum: 0xFFE7AF06
Bitstream
In FsblHookBeforeBitstreamDload function
PCAP:StatusReg = 0x40000A30
PCAP:device ready
PCAP:Clear done
Level Shifter Value = 0xA
Devcfg Status register = 0x40000A30
PCAP:Fabric is Initialized done
PCAP register dump:
PCAP CTRL 0xF8007000: 0x4C00E07F
PCAP LOCK 0xF8007004: 0x0000001A
PCAP CONFIG 0xF8007008: 0x00000508
PCAP ISR 0xF800700C: 0x0802000B
PCAP IMR 0xF8007010: 0xFFFFFFFF
PCAP STATUS 0xF8007014: 0x50000F30
PCAP DMA SRC ADDR 0xF8007018: 0x00100001
PCAP DMA DEST ADDR 0xF800701C: 0xFFFFFFFF
PCAP DMA SRC LEN 0xF8007020: 0x0007F2E8
PCAP DMA DEST LEN 0xF8007024: 0x0007F2E8
PCAP ROM SHADOW CTRL 0xF8007028: 0xFFFFFFFF
PCAP MBOOT 0xF800702C: 0x0000C000
PCAP SW ID 0xF8007030: 0x00000000
PCAP UNLOCK 0xF8007034: 0x757BDF0D
PCAP MCTRL 0xF8007080: 0x30800100

DMA Done !

FPGA Done !
In FsblHookAfterBitstreamDload function
Partition Number: 2
Header Dump
Image Word Len: 0x000216CC
Data Word Len: 0x000216CC
Partition Word Len:0x000216CC
Load Addr: 0x04000000
Exec Addr: 0x04000000
Partition Start: 0x000868C0
Partition Attr: 0x00000010
Partition Checksum Offset: 0x00000000
Section Count: 0x00000001
Checksum: 0xF7F1506A
Application
Handoff Address: 0x04000000
In FsblHookBeforeHandoff function
SUCCESSFUL_HANDOFF
FSBL Status = 0x1

U-Boot 2016.07-g7640c9f-dirty (Feb 27 2018 — 17:57:23 +0800)

Model: Zynq MicroZED Board
Board: Xilinx Zynq
DRAM:
dram_init: sys_sdram_size = 0x10000000
dram_init: sys_sdram_size = 256 MB
dram_init: gd->ram_size = 0x0f000000
ECC disabled 240 MiB
NAND:  256 MiB
MMC:   sdhci@e0100000: 0
Invalid bus 0 (err=-1)
*** Warning — spi_flash_probe() failed, using default environment

In:    serial@e0000000
Out:   serial@e0000000
Err:   serial@e0000000
Model: Zynq MicroZED Board
Board: Xilinx Zynq
board_late_init: bootargs: mem=240M console=ttyPS0,115200 ramdisk_size=33554432        root=/dev/ram rw earlyprintk

— boot gpio value = 0x003fff3c
— nand boot nand —

Net:   — phy_broadcom_init
ZYNQ GEM: e000b000, phyaddr 0, interface gmii
— zynq_gem_probe
— mdio_register
— mdio_register 1
— mdio_register 2
— mdio_register 3
— zynq_phy_init: interface = 1
— zynq_phy_init
 0000000000
PHY is not detected
GEM PHY init failed
No ethernet found.
Hit any key to stop autoboot:  0
Copying Linux from NAND flash to RAM…

NAND read: device 0 offset 0x2000000, size 0x800000
 8388608 bytes read: OK

NAND read: device 0 offset 0x1a00000, size 0x20000
 131072 bytes read: OK
Copying ramdisk…

NAND read: device 0 offset 0x2800000, size 0x2000000
 33554432 bytes read: OK
## Booting kernel from Legacy Image at 02000000 …
   Image Name:   Linux-4.6.0-xilinx-gff8137b-dirt
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3851576 Bytes = 3.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum … OK
## Loading init Ramdisk from Legacy for 0, Image at 04000000 …
   Image Name:
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    12743872 Bytes = 12.2 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum … OK
get ramdisk ok
## Flattened Device Tree blob at 03000000
   Booting using the fdt blob at 0x3000000
   Loading Kernel Image … OK
   Loading Ramdisk to 0ced9000, end 0db004c0 … OK
   Loading Device Tree to 0ced4000, end 0ced8d99 … OK

Starting kernel …

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #22 SMP PREEMPT Fri Dec 22 12:25:44 CST 2017
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 205936K/245760K available (5317K kernel code, 230K rwdata, 1844K rodata, 1024K init, 222K bss, 23440K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 — 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 — 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 — 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 — 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 — 0xc0000000   (   2 MB)
    modules : 0xbf000000 — 0xbfe00000   (  14 MB)
      .text : 0xc0008000 — 0xc07fe410   (8154 kB)
      .init : 0xc0800000 — 0xc0900000   (1024 kB)
      .data : 0xc0900000 — 0xc0939a60   ( 231 kB)
       .bss : 0xc0939a60 — 0xc09713e8   ( 223 kB)
Preemptible hierarchical RCU implementation.
        Build-time adjustment of leaf fanout to 32.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80×30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 — 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 — Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs…
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12448K (cced9000 — cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000

[drm]

 Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver — 3.2.6-k
e1000e: Copyright(c) 1999 — 2015 Intel Corporation.
ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
5 ofpart partitions found on MTD device pl35x-nand
Creating 5 MTD partitions on «pl35x-nand»:
0x000000000000-0x000002800000 : «BOOT.bin-env-dts-kernel»
0x000002800000-0x000004800000 : «ramfs»
0x000004800000-0x000005000000 : «configs»
0x000005000000-0x000006000000 : «reserve»
0x000006000000-0x000008000000 : «ramfs-bak»
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for ‘xlnx,zynq-ddrc-a05’
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn’t mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0800000 — c0900000)
INIT: version 2.88 booting
mount: mounting devtmpfs on /dev failed: Device or resource busy
Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory
bootlogd.
Starting Monitor-ipsig daemon: monitor-ipsig.
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
check mouted config
mounting config
Starting syslogd/klogd: done
killall: udhcpc: no process killed
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.20.2) started
Sending discover…
Sending discover…
Sending discover…
Sending discover…
Sending discover…
Sending discover…
Sending discover…
Sending discover…
Sending discover…
Sending discover…
No lease, forking to background
Error resolving pool.ntp.org: System error (-11)
 1 Jan 00:00:35 ntpdate[893]: Can’t find host pool.ntp.org: System error (-11)
 1 Jan 00:00:35 ntpdate[893]: no servers can be used, exiting
Starting ntpd: done
Starting Avahi Daemon: avahi-daemon.
Starting Lighttpd Web Server: lighttpd.
Starting Cgminer daemon: ping: sendto: Network is unreachable
192.168.1.1 is reachable
No bitmain_axi.ko
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcf99c000
*base_vir_addr = 0x200ac513
memory_size = 235792
fpga_mem_offset_addr=0x0F000000
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
PARAMS = —version-file /usr/bin/compile_time
cgminer.
Starting Monitor-recobtn daemon: monitor-recobtn.
INIT: Entering runlevel: 5
Stopping Bootlog daemon: bootlogd.

.—O—.
|       |                  .-.           o o
|   |   |——.——.——.| |   .—-..——.——.
|       |     | __  |  —‘| ‘—.|  .-‘|     |     |
|   |   |  |  |     |—  ||  —‘|  |  |  ‘  | | | |
‘—‘—‘—‘—‘—.  |——»—-»—‘  ‘——‘-‘-‘-‘
                -‘  |
                ‘—‘

The Angstrom Distribution antMiner ttyPS0

Angstrom v2013.06 — Kernel 4.6.0-xilinx-gff8137b-dirty

antMiner login:

tags: MinerCtrlboard V1.1 Control Board Z9, V9, Z9 mini, S9k, S9 SE

ссылка на статью: ремонт платы Bitmain D3, L3+ http://agansk.ru/tech/2017/11/30/control-board-bitmain-antminer-d3-dump-29f2g08abaea/

2 thoughts on “Antminer Z9 Miner_Ctrlboard_V1.1 ремонт платы, фото

  1. Booting Linux on physical CPU 0x0
    Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #22 SMP PREEMPT Fri Dec 22 12:25:44 CST 2017
    CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
    CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
    Machine model: Xilinx Zynq
    cma: Reserved 16 MiB at 0x0e000000
    Memory policy: Data cache writealloc
    On node 0 totalpages: 61440
    free_area_init_node: node 0, pgdat c0938d00, node_mem_map cde10000
    Normal zone: 480 pages used for memmap
    Normal zone: 0 pages reserved
    Normal zone: 61440 pages, LIFO batch:15
    percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
    pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
    pcpu-alloc: [0] 0 [0] 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
    Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
    PID hash table entries: 1024 (order: 0, 4096 bytes)
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 205936K/245760K available (5317K kernel code, 230K rwdata, 1844K rodata, 1024K init, 222K bss, 23440K reserved, 16384K cma-reserved, 0K highmem)
    Virtual kernel memory layout:
    vector : 0xffff0000 — 0xffff1000 ( 4 kB)
    fixmap : 0xffc00000 — 0xfff00000 (3072 kB)
    vmalloc : 0xcf800000 — 0xff800000 ( 768 MB)
    lowmem : 0xc0000000 — 0xcf000000 ( 240 MB)
    pkmap : 0xbfe00000 — 0xc0000000 ( 2 MB)
    modules : 0xbf000000 — 0xbfe00000 ( 14 MB)
    .text : 0xc0008000 — 0xc07fe410 (8154 kB)
    .init : 0xc0800000 — 0xc0900000 (1024 kB)
    .data : 0xc0900000 — 0xc0939a60 ( 231 kB)
    .bss : 0xc0939a60 — 0xc09713e8 ( 223 kB)
    Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
    NR_IRQS:16 nr_irqs:16 16
    efuse mapped to cf800000
    ps7-slcr mapped to cf802000
    L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
    L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
    L2C-310 erratum 769419 enabled
    L2C-310 enabling early BRESP for Cortex-A9
    L2C-310 full line of zeros enabled for Cortex-A9
    L2C-310 ID prefetch enabled, offset 1 lines
    L2C-310 dynamic clock gating enabled, standby mode enabled
    L2C-310 cache controller enabled, 8 ways, 512 kB
    L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
    zynq_clock_init: clkc starts at cf802100
    Zynq clock init
    sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
    clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
    Switching to timer-based delay loop, resolution 3ns
    clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
    ps7-ttc #0 at cf80a000, irq=18
    Console: colour dummy device 80×30
    Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    CPU: Testing write buffer coherency: ok
    CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    Setting up static identity map for 0x100000 — 0x100058
    CPU1: failed to boot: -1
    Brought up 1 CPUs
    SMP: Total of 1 processors activated (666.66 BogoMIPS).
    CPU: All CPU(s) started in SVC mode.
    devtmpfs: initialized
    VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
    clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    pinctrl core: initialized pinctrl subsystem
    NET: Registered protocol family 16
    DMA: preallocated 256 KiB pool for atomic coherent allocations
    cpuidle: using governor menu
    hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
    hw-breakpoint: maximum watchpoint size is 4 bytes.
    zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
    vgaarb: loaded
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    media: Linux media interface: v0.10
    Linux video capture interface: v2.00
    pps_core: LinuxPPS API ver. 1 registered
    pps_core: Software ver. 5.3.6 — Copyright 2005-2007 Rodolfo Giometti
    PTP clock support registered
    EDAC MC: Ver: 3.0.0
    Advanced Linux Sound Architecture Driver Initialized.
    clocksource: Switched to clocksource arm_global_timer
    NET: Registered protocol family 2
    TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    UDP hash table entries: 256 (order: 1, 8192 bytes)
    UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    NET: Registered protocol family 1
    RPC: Registered named UNIX socket transport module.
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    PCI: CLS 0 bytes, default 64
    Trying to unpack rootfs image as initramfs…
    rootfs image is not initramfs (no cpio magic); looks like an initrd
    Freeing initrd memory: 12448K (cced9000 — cdb01000)
    hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
    futex hash table entries: 512 (order: 3, 32768 bytes)
    workingset: timestamp_bits=28 max_order=16 bucket_order=0
    jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
    dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
    e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
    console [ttyPS0] enabled
    xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
    [drm] Initialized drm 1.1.0 20060810
    brd: module loaded
    loop: module loaded
    CAN device driver interface
    gpiod_set_value: invalid GPIO
    libphy: MACB_mii_bus: probed
    macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
    Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
    e1000e: Intel(R) PRO/1000 Network Driver — 3.2.6-k
    e1000e: Copyright(c) 1999 — 2015 Intel Corporation.
    ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
    ehci-pci: EHCI PCI platform driver
    usbcore: registered new interface driver usb-storage
    mousedev: PS/2 mouse device common for all mice
    i2c /dev entries driver
    Xilinx Zynq CpuIdle Driver started
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    sdhci-pltfm: SDHCI platform and OF driver helper
    mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
    ledtrig-cpu: registered to indicate activity on CPUs
    usbcore: registered new interface driver usbhid
    usbhid: USB HID core driver
    nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
    nand: Micron MT29F2G08ABAEAWP
    nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
    nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
    Bad block table found at page 131008, version 0x01
    Bad block table found at page 130944, version 0x01
    5 ofpart partitions found on MTD device pl35x-nand
    Creating 5 MTD partitions on «pl35x-nand»:
    0x000000000000-0x000002800000 : «BOOT.bin-env-dts-kernel»
    0x000002800000-0x000004800000 : «ramfs»
    0x000004800000-0x000005000000 : «configs»
    0x000005000000-0x000006000000 : «reserve»
    0x000006000000-0x000008000000 : «ramfs-bak»
    NET: Registered protocol family 10
    sit: IPv6 over IPv4 tunneling driver
    NET: Registered protocol family 17
    can: controller area network core (rev 20120528 abi 9)
    NET: Registered protocol family 29
    can: raw protocol (rev 20120528)
    can: broadcast manager protocol (rev 20120528 t)
    can: netlink gateway (rev 20130117) max_hops=1
    zynq_pm_ioremap: no compatible node found for ‘xlnx,zynq-ddrc-a05’
    zynq_pm_late_init: Unable to map DDRC IO memory.
    Registering SWP/SWPB emulation handler
    hctosys: unable to open rtc device (rtc0)
    ALSA device list:
    No soundcards found.
    RAMDISK: gzip image found at block 0
    EXT4-fs (ram0): couldn’t mount as ext3 due to feature incompatibilities
    EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
    VFS: Mounted root (ext4 filesystem) on device 1:0.
    devtmpfs: mounted
    Freeing unused kernel memory: 1024K (c0800000 — c0900000)
    EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
    random: dd urandom read with 0 bits of entropy available
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
    macb e000b000.ethernet eth0: link up (100/Full)
    IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    In axi fpga driver!
    request_mem_region OK!
    AXI fpga dev virtual address is 0xcf99c000
    *base_vir_addr = 0x200ac513
    In fpga mem driver!
    request_mem_region OK!
    fpga mem virtual address is 0xd2000000
    random: nonblocking pool is initialized
    Oct 23 17:52:52 (none) local0.err cgminer: Miner compile time: Fri May 17 16:21:07 CST 2019 type: Antminer Z9
    Oct 23 17:52:52 (none) local0.warn cgminer: Started cgminer 4.9.0
    Oct 23 17:52:52 (none) local0.warn cgminer[958]: bitmain_ZCASH_init
    Oct 23 17:52:52 (none) local0.notice cgminer[958]: No 2 Fan find, check again
    Oct 23 17:52:54 (none) local0.notice cgminer[958]: fan-num 2 fan-map 3
    Oct 23 17:52:54 (none) local0.notice cgminer[958]: check_chain
    Oct 23 17:52:54 (none) local0.notice cgminer[958]: Chain 0 existed!
    Oct 23 17:52:54 (none) local0.notice cgminer[958]: Chain 1 existed!
    Oct 23 17:52:54 (none) local0.notice cgminer[958]: Chain 2 existed!
    Oct 23 17:52:54 (none) local0.notice cgminer[958]: chain0 every_chain_reset_PIC16F1704_pic_new
    Oct 23 17:52:55 (none) local0.notice cgminer[958]: reset_PIC16F1704_pic_new ok
    Oct 23 17:52:55 (none) local0.notice cgminer[958]: chain1 every_chain_reset_PIC16F1704_pic_new
    Oct 23 17:52:56 (none) local0.notice cgminer[958]: reset_PIC16F1704_pic_new ok
    Oct 23 17:52:56 (none) local0.notice cgminer[958]: chain2 every_chain_reset_PIC16F1704_pic_new
    Oct 23 17:52:57 (none) local0.notice cgminer[958]: reset_PIC16F1704_pic_new ok
    Oct 23 17:52:58 (none) local0.notice cgminer[958]: chain0 every_chain_jump_from_loader_to_app_PIC16F1704_new
    Oct 23 17:52:58 (none) local0.notice cgminer[958]: jump_from_loader_to_app_PIC16F1704_new ok
    Oct 23 17:52:58 (none) local0.notice cgminer[958]: chain1 every_chain_jump_from_loader_to_app_PIC16F1704_new
    Oct 23 17:52:59 (none) local0.notice cgminer[958]: jump_from_loader_to_app_PIC16F1704_new ok
    Oct 23 17:52:59 (none) local0.notice cgminer[958]: chain2 every_chain_jump_from_loader_to_app_PIC16F1704_new
    Oct 23 17:52:59 (none) local0.notice cgminer[958]: jump_from_loader_to_app_PIC16F1704_new ok
    Oct 23 17:53:01 (none) local0.notice cgminer[958]: reset_all_hash_board_low 3851
    Oct 23 17:53:01 (none) local0.notice cgminer[958]: pic_heart_beat_func_new
    Oct 23 17:53:01 (none) local0.notice cgminer[958]: every_chain_enable_PIC16F1704_dc_dc_new
    Oct 23 17:53:01 (none) local0.notice cgminer[958]: enable_PIC16F1704_dc_dc_new ok
    Oct 23 17:53:01 (none) local0.notice cgminer[958]: enable_PIC16F1704_dc_dc_new ok
    Oct 23 17:53:02 (none) local0.notice cgminer[958]: enable_PIC16F1704_dc_dc_new ok
    Oct 23 17:53:02 (none) local0.notice cgminer[958]: reset_all_hash_board_high 3857
    Oct 23 17:53:02 (none) local0.notice cgminer[958]: tty_init
    Oct 23 17:53:02 (none) local0.notice cgminer[958]: tty_init_chain chainid = 0
    Oct 23 17:53:02 (none) local0.err cgminer[958]: create rx read thread for chain 0 ok
    Oct 23 17:53:02 (none) local0.notice cgminer[958]: Start A New Asic Response.Chain Id:[0]
    Oct 23 17:53:03 (none) local0.err cgminer[958]: create tx read thread for chain 0 ok
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: open device over
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: tty_init_chain chainid = 1
    Oct 23 17:53:03 (none) local0.err cgminer[958]: create rx read thread for chain 1 ok
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: Start A New Asic Response.Chain Id:[1]
    Oct 23 17:53:03 (none) local0.err cgminer[958]: create tx read thread for chain 1 ok
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: open device over
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: tty_init_chain chainid = 2
    Oct 23 17:53:03 (none) local0.err cgminer[958]: create rx read thread for chain 2 ok
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: Start A New Asic Response.Chain Id:[2]
    Oct 23 17:53:03 (none) local0.err cgminer[958]: create tx read thread for chain 2 ok
    Oct 23 17:53:03 (none) local0.notice cgminer[958]: open device over
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:06 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid0 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid1 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:07 (none) local0.notice cgminer[958]: chainid2 set_io_drive_strength_chain: IO drive = 02113111
    Oct 23 17:53:10 (none) local0.notice cgminer[958]: check_every_chain_asic_number
    Oct 23 17:53:11 (none) local0.notice cgminer[958]: check_asic_reg: chain J0 has 16 ASIC
    Oct 23 17:53:13 (none) local0.notice cgminer[958]: check_asic_reg: chain J1 has 16 ASIC
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: check_asic_reg: chain J2 has 16 ASIC
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: calculate_address_interval:addrInterval = 16
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: chainid0 set_frequency_chain freq=550
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: chainid1 set_frequency_chain freq=550
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: chainid2 set_frequency_chain freq=550
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: set_ticket_mask_chain chainID0 ticket_mask = 0x0000000d
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: set_ticket_mask_chain chainID1 ticket_mask = 0x0000000d
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: set_ticket_mask_chain chainID2 ticket_mask = 0x0000000d
    Oct 23 17:53:15 (none) local0.notice cgminer[958]: software_set_address_chain chainID0 asics 16 addrInterval 16
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: software_set_address_chain chainID1 asics 16 addrInterval 16
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: software_set_address_chain chainID2 asics 16 addrInterval 16
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: chainid0 set_core_timeout_chain: core timeout = 00100000
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: chainid1 set_core_timeout_chain: core timeout = 00100000
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: chainid2 set_core_timeout_chain: core timeout = 00100000
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: chainID0 set_txn_data_chain txndata 0 txnzero 0
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: chainID1 set_txn_data_chain txndata 0 txnzero 0
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: chainID2 set_txn_data_chain txndata 0 txnzero 0
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: enable_read_temperature_from_asic_chain: reg_value=0x07006061 chainid 0
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: enable_read_temperature_from_asic_chain: reg_value=0x07006061 chainid 1
    Oct 23 17:53:16 (none) local0.notice cgminer[958]: enable_read_temperature_from_asic_chain: reg_value=0x07006061 chainid 2
    Oct 23 17:53:17 (none) local0.notice cgminer[958]: dev.timeout = 30000000 us
    Oct 23 17:53:17 (none) local0.notice cgminer[958]: bitmain_ZCASH_init: fan_eft : 0 fan_pwm : 30
    Oct 23 17:53:20 (none) local0.notice cgminer[958]: 414692one
    Oct 23 17:53:20 (none) local0.err cgminer[958]: cgminer time error total_secs = 1571853200.100708 last_total_secs = 1.000000
    Oct 23 17:53:20 (none) local0.info cgminer[958]: Pool 0 extranonce set to b32495acf1
    Oct 23 17:53:20 (none) local0.info cgminer[958]: Pool 2 extranonce set to ae24a45f80
    Oct 23 17:53:20 (none) local0.info cgminer[958]: Pool 1 extranonce set to ae24a45f82
    Oct 23 17:53:26 (none) local0.warn cgminer[958]: API running in IP access mode on port 4028 (8)
    Oct 24 00:59:52 (none) local0.warn cgminer[958]: Lost 1 shares due to stratum disconnect on pool 0
    Oct 24 00:59:53 (none) local0.info cgminer[958]: Pool 0 extranonce set to b3249d3073
    Oct 24 02:26:38 (none) local0.warn cgminer[958]: Lost 2 shares due to stratum disconnect on pool 0
    Oct 24 02:26:39 (none) local0.info cgminer[958]: Pool 0 extranonce set to af249b3cad

  2. Mem: 92140K used, 143652K free, 0K shrd, 642924K buff, 642968K cached
    CPU: 9% usr 90% sys 0% nic 0% idle 0% io 0% irq 0% sirq
    Load average: 2.18 2.02 2.04 2/105 27843
    PID PPID USER STAT VSZ %VSZ %CPU COMMAND
    958 955 root S < 205m 89% 82% /usr/bin/cgminer —version-file /usr/bin/compile_time —default-config /config/cgminer.conf -T —syslog
    902 1 root S 3328 1% 0% /usr/bin/ntpd -p /var/run/ntp.pid -g
    916 1 root S 2984 1% 0% /usr/sbin/lighttpd -f /etc/lighttpd.conf
    908 1 avahi S 2732 1% 0% avahi-daemon: running [antMiner-2.local]
    909 908 avahi S 2732 1% 0% avahi-daemon: chroot helper
    955 1 root S 2620 1% 0% {screen} SCREEN -S cgminer -t cgminer -m -d /usr/bin/cgminer —version-file /usr/bin/compile_time —default-config /config/cgminer.conf -T —syslog
    970 1 root S 2152 1% 0% {monitorcg} /bin/sh /sbin/monitorcg
    704 1 root S 2152 1% 0% /sbin/syslogd -n -O /var/log/messages
    706 1 root S 2152 1% 0% /sbin/klogd -n
    27272 27268 root R 2152 1% 0% top -b -n 1
    894 1 root S 2152 1% 0% udhcpc -b -t 10 -A 10 -x hostname antMiner -i eth0
    27268 916 root S 2152 1% 0% /bin/sh /www/pages/cgi-bin/monitor.cgi
    27273 27268 root S 2152 1% 0% /bin/sh /www/pages/cgi-bin/monitor.cgi
    19068 970 root S 2020 1% 0% sleep 20s
    968 1 root S 1912 1% 0% /sbin/getty 115200 ttyPS0
    969 1 root S 1912 1% 0% /sbin/getty 38400 tty1
    1 0 root S 1656 1% 0% init [5]
    674 1 root S 1640 1% 0% /usr/bin/monitor-ipsig
    960 1 root S 1636 1% 0% /usr/bin/monitor-recobtn /usr/bin/factory_config_reset.sh
    3 2 root SW 0 0% 0% [ksoftirqd/0]
    7 2 root SW 0 0% 0% [rcu_preempt]
    59 2 root SW 0 0% 0% [kworker/0:1]
    18 2 root SW 0 0% 0% [kworker/u4:1]
    2 0 root SW 0 0% 0% [kthreadd]
    4 2 root SW 0 0% 0% [kworker/0:0]
    5 2 root SW< 0 0% 0% [kworker/0:0H]
    6 2 root SW 0 0% 0% [kworker/u4:0]
    8 2 root SW 0 0% 0% [rcu_sched]
    9 2 root SW 0 0% 0% [rcu_bh]
    10 2 root SW 0 0% 0% [migration/0]
    11 2 root SW 0 0% 0% [cpuhp/0]
    12 2 root SW 0 0% 0% [cpuhp/1]
    13 2 root SW 0 0% 0% [migration/1]
    14 2 root SW 0 0% 0% [ksoftirqd/1]
    15 2 root SW 0 0% 0% [kworker/1:0]
    16 2 root SW< 0 0% 0% [kworker/1:0H]
    17 2 root SW 0 0% 0% [kdevtmpfs]
    246 2 root SW 0 0% 0% [oom_reaper]
    247 2 root SW< 0 0% 0% [writeback]
    249 2 root SW< 0 0% 0% [crypto]
    250 2 root SW< 0 0% 0% [bioset]
    252 2 root SW< 0 0% 0% [kblockd]
    281 2 root SW< 0 0% 0% [edac-poller]
    293 2 root SW< 0 0% 0% [watchdogd]
    377 2 root SW< 0 0% 0% [rpciod]
    391 2 root SW 0 0% 0% [kswapd0]
    392 2 root SW< 0 0% 0% [vmstat]
    393 2 root SW< 0 0% 0% [nfsiod]
    424 2 root SW< 0 0% 0% [bioset]
    425 2 root SW< 0 0% 0% [bioset]
    426 2 root SW< 0 0% 0% [bioset]
    427 2 root SW< 0 0% 0% [bioset]
    428 2 root SW< 0 0% 0% [bioset]
    429 2 root SW< 0 0% 0% [bioset]
    430 2 root SW< 0 0% 0% [bioset]
    431 2 root SW< 0 0% 0% [bioset]
    432 2 root SW< 0 0% 0% [bioset]
    433 2 root SW< 0 0% 0% [bioset]
    434 2 root SW< 0 0% 0% [bioset]
    435 2 root SW< 0 0% 0% [bioset]
    436 2 root SW< 0 0% 0% [bioset]
    437 2 root SW< 0 0% 0% [bioset]
    438 2 root SW< 0 0% 0% [bioset]
    439 2 root SW< 0 0% 0% [bioset]
    473 2 root SW< 0 0% 0% [bioset]
    476 2 root SW< 0 0% 0% [bioset]
    478 2 root SW< 0 0% 0% [bioset]
    481 2 root SW< 0 0% 0% [bioset]
    484 2 root SW< 0 0% 0% [bioset]
    487 2 root SW< 0 0% 0% [bioset]
    490 2 root SW< 0 0% 0% [bioset]
    493 2 root SW< 0 0% 0% [bioset]
    568 2 root SW< 0 0% 0% [kpsmoused]
    593 2 root SW 0 0% 0% [irq/155-mmc0]
    609 2 root SW< 0 0% 0% [bioset]
    614 2 root SW< 0 0% 0% [bioset]
    619 2 root SW< 0 0% 0% [bioset]
    624 2 root SW< 0 0% 0% [bioset]
    629 2 root SW< 0 0% 0% [bioset]
    641 2 root SW< 0 0% 0% [ipv6_addrconf]
    649 2 root SW< 0 0% 0% [deferwq]
    651 2 root SW< 0 0% 0% [ext4-rsv-conver]
    694 2 root SWN 0 0% 0% [jffs2_gcd_mtd2]

Добавить комментарий

Ваш e-mail не будет опубликован. Обязательные поля помечены *